Flight stack SpeedyBee F405 v3 ESC 50A

Description Flight stack SpeedyBee F405 v3 ESC 50A: F405 V3 FC flight controller and 50A 3-6s BLHeli_S 4-in-1 ESC speed controller in 30x30mm size. This unique stack allows for Bluetooth connectivity and setup, and is equipped with built-in 4-level battery indicators, 1500µF filter capacitor, integrated barometer, and many other features that make it the perfect choice for any FPV pilot. Features Dedicated DJI Air Unit connector for quick connection 4 x UART for connecting devices: receiver, VTX, camera, GPS SD card slot supports up to 4 GB of Blackbox data BEC: 9V 2A and 5V 2A 4-level LED battery indicator 8 outputs for motors: m1-m8 Built-in barometer Control via Bluetooth Characteristics Flight controller F405 V3 FC: MCU: STM32F405 IMU (Gyro): BMI270 USB Port: Type-C Barometer: built-in OSD Chip: AT7456E chip BLE Bluetooth: Supported. Used to configure the flight controller. DJI Air Unit connection method: via 6-pin connector or soldering Blackbox MicroSD memory card support: Yes BetaFlight camera control panel: yes Input current sensor: yes Input power: 3S – 6S Lipo ESC outputs: M1 – M4 on the bottom side and M5-M8 on the top UART: 6 sets (UART1, UART2, UART3, UART4 (for ESC telemetry), UART6) ESC: Telemetry UART R5(UART5) I2C: supported Buzzer: yes BOOT button: yes RSSI input: yes SmartPort: yes Firmware support: BetaFlight(Default), EMUFlight, INAV Firmware target: SPEEDYBEEF405V3 Mounting scheme: 30.5×30.5mm (4mm hole diameter) Dimensions: 41.6×39.4×7.8mm Weight: 9.6g *Note: BOOT button. Usage options: [А]. Press and hold the BOOT button and turn on the FC at the same time to make the FC enter DFU mode, this is for flashing the FC when the firmware has flown. [Б]. When the PC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to the LED1-LED4 connectors on the bottom side. By default, press the BOOT button briefly to switch to the LED display mode. Press and hold the BOOT button to toggle between SpeedyBee-LED mode and BF-LED mode. In the BF-LED mode, all LED1-LED4 bands will be controlled by the Betaflight firmware. SpeedyBee BLS 50A 30×30 4-in-1 ESC speed controller Firmware: BLHeli_S JH50 Wireless configuration: SpeedyBee app support Link to PC Configurator: https://esc-configurator.com/ Constant current: 50A x 4 Peak current: 55A(5sec) TVS protection: yes External capacitor: 1500uF Low ESR Capacitor (included) ESC Protocol: DSHOT300/600 Input power: 3-6S LiPo Output power: VBAT Current sensor: yes Mounting size: 30.5×30.5mm (4mm hole diameter) Dimensions: 45.6x44x6.1mm Weight: 13.8g Package contents F405 V3 FC 1x SH 1.0mm 30mm 8pin cable (for FC-ESC connection) 1x SpeedyBee F405 V3 Flight Controller – 30×30 5x M3x8mm silicone bushings (for FC) 1x DJI 6pin cable (80mm) 50A 3-6s BLHeli_S 4-in-1 ESC 1x SH 1.0mm 30mm 8pin cable (for FC-ESC connection) 1x SpeedyBee 50A 3-6S BLHeli_S 4-in-1 ESC – 30×30 5x M3x8.1mm silicone bushings (for ESC) 1x 35V 1500uF Low ESR Capacitor 1x XT60 power cable (70mm) 5x M3 silicone O-rings